How to Use

How to Use Auto Bros Products

Find your product below for a practical starting guide. Directions are based on our current product listings. Always follow the instructions on the bottle or supplied instruction sheet if they differ. Where a listing does not specify dilution, contact time, removal method or curing time, check the label or contact Auto Bros before use. Do not guess these settings.

Before You Start

• Work in the shade on cool surfaces and test a small, hidden area first.
• Read the label for surface compatibility, protective equipment and ventilation requirements. Never mix chemicals.
• Use separate clean towels, pads and brushes for paint, wheels and interiors.
• Do not let cleaners dry on a surface. Keep dressings off tyre tread, brakes, pedals and steering wheels.
• Keep products away from children and pets.

Wash & Pre-Wash

Goldmine Car Shampoo

Rinse loose dirt from the vehicle. Prepare the shampoo at the dilution stated on the bottle, wash gently from top to bottom with a clean wash mitt, rinse thoroughly and dry with a clean microfibre towel. The listing does not specify a dilution ratio.

Ultimate Kool Snow Foam

Use as a pre-wash before your regular bucket wash. Prepare and apply using the dilution and equipment instructions on the label. Rinse away loosened dirt before contact washing. The listing does not specify dilution or dwell time.

Saver Snow Foam

For foam-cannon use, the listing gives 100 ml product per 1 litre of water. Apply to cool surfaces and rinse before the foam dries. For bucket washing, check the bottle before mixing: the listing states both 1:100 and 20–25 ml per 5 litres of water, which are not equivalent. Follow the confirmed bottle directions rather than choosing between these figures.

Car Shampoo Bucket Wash

Rinse the vehicle first. Mix the jelly shampoo according to the bottle directions, wash with a clean mitt, then rinse and dry. The listing does not provide a dilution ratio. Keep the included cloths and applicators clean and use them only for their intended task.

Touchless Clean

This high-alkaline pre-soak is intended for touchless washing. Use on a cool vehicle in the shade, with the dilution, equipment and contact time specified on the label. Rinse thoroughly before drying. Confirm compatibility with your existing protection before use.

Targeted Exterior Cleaning

Gum, Adhesive & Tar Remover

Use for sticky adhesive, tape residue and tar on surfaces approved on the bottle. Test a hidden area first. Follow the label for application, contact time and removal, then clean the treated area as directed. Do not scrape paint or assume every vinyl finish is compatible.

GTBT Cleaner

Use to target glue, tar, bugs and tree sap on compatible surfaces. Follow the bottle instructions for application and removal. The listing also describes removal of wax, grease, silicone and polish residues, so do not treat it as a protection-preserving maintenance wash. Prepare and protect the surface again where required.

Converting Cleaner

Use only on surfaces confirmed compatible with this iron and fallout remover. Test first, follow the label's dilution and contact time, and remove or rinse exactly as instructed. The listing does not specify a dwell time or colour-change procedure.

Hard Water Scale Remover

This is an acid-based water-spot remover. Test a small hidden area first and use only on finishes approved by the label. Avoid rubber seals and unpainted plastic trim. Follow the label's protective-equipment, contact-time and rinsing instructions; do not improvise dilution or dwell time.

Alkaline Tyre & Plastic Trim Cleaner

Use on compatible tyres, alloy wheels and plastic trim. Do not apply to hot surfaces. Test first, use the label dilution and application method, and rinse thoroughly after cleaning. Let the surface dry before applying a suitable dressing.

Engine Cleaner Degreaser

Use for engine-bay grease and oil only where compatible. Let the engine cool and follow the vehicle manufacturer's cleaning precautions. Protect sensitive electrical components and air intakes. Follow the product label for dilution, agitation and removal; do not pressure-wash sensitive components.

Thunder Engine Bay Degreaser

This heavy-duty cleaner is listed for engines, tyres and plastic surfaces. Check compatibility and the bottle's dilution instructions before use. For engine bays, let the engine cool and protect electrical components and air intakes. Follow the specified removal method rather than treating every surface alike.

Glass & Washer Care

Windshield Washer Fluid

1. Identify the windshield washer reservoir, usually marked with a wiper symbol. Do not confuse it with coolant or brake-fluid reservoirs.
2. Pour the ready-to-use fluid directly into the washer reservoir. No dilution is needed.
3. Replace the cap securely and operate the washer system normally.

Glass Cleaner Tablets

The listing directs you to add a tablet to a washer reservoir filled with water. Check the pack for the required water volume and dissolution instructions before use; the listing does not specify them. Store tablets in a cool, dry place away from children.

Interior & Leather Care

Interior Cleaner Spray

1. Test the material first. Apply to a microfibre cloth or a compatible surface.
2. Wipe gently using circular or straight motions.
3. For stubborn stains, the listing specifies a 30-second dwell before wiping, provided the surface is compatible.
4. Buff with a clean, dry microfibre towel.

For screens and sensitive electronics, apply to the cloth, never directly to the device, and follow the device manufacturer's care instructions.

All Purpose Extraction Cleaner

Use on compatible fabric, carpet, mats and upholstery. Vacuum loose dirt first and test colourfastness. Follow the product and extraction machine instructions for dilution and use. The listing recommends a second pre-treatment application on heavily soiled areas before extraction. Avoid over-wetting and let the material dry fully.

Leather Care Combo Kit

Use the Leather Cleaner first to remove dirt and oils, following its label. Then apply the Leather Conditioner according to its separate directions. Test both products on a hidden area and check suitability for your leather finish. The listing suggests maintenance every 1–3 months; adjust to the leather manufacturer's guidance and condition.

MPSP Spray Polish

This silicone-based dressing is listed for dashboards, plastic, rubber, tyres, vinyl and leather. Clean the compatible surface first, then follow the bottle's application and buffing instructions. For interiors, use a controlled application and keep it away from screens, controls and grip surfaces.

MPSP Cream

Use on compatible plastic, leather, rubber and vinyl surfaces such as door trims, tyres, bumpers and rubber seals. Clean first, test a hidden area and follow the label for application and excess removal. Do not apply to pedals, steering wheels, tyre tread or braking surfaces.

Car Fragrance Spray

Choose Denim Freshener, Merry Mist, Musk Mani or Ocean Breeze. Follow the bottle for spray quantity and placement. Avoid spraying towards people, pets, controls, screens or visibility-critical surfaces. Check material compatibility before spraying directly onto any surface; the listing does not specify a spray count.

Tyre & Plastic Trim Protection

Instant Tyre & Trim Restorer

Clean and dry compatible tyre sidewalls or exterior trim first. Follow the label for applying this oil-based dressing and removing excess. Keep it off tyre tread, brakes and walking or grip surfaces.

Plastic Serum

Use on compatible exterior unpainted plastic trim, including bumpers, door handles and mirror housings. Clean and dry the area, test first and follow the bottle for application, levelling and drying. The listing does not specify application quantity or curing time.

Cera Trim Restorer

Use on compatible unpainted exterior plastic. Clean and prepare the trim as directed, then use the supplied gloves and non-absorbent application cloth according to the instructions. Confirm application quantity, excess-removal method and curing time before starting. These details are not specified in the listing.

Paint Correction

Wash and dry first, inspect the paint and make a test spot. Start with the least aggressive suitable product; not every vehicle needs every correction stage. Machine settings depend on the machine, pad, paint and product instructions. Heavy cutting and rotary polishing are best handled by experienced users.

1P Cutting Compound

1. Apply a small amount to a suitable cutting pad.
2. Work a small section with a DA or rotary polisher, using the product and machine instructions. The listing describes medium speed but gives no numeric setting.
3. Wipe residue with a clean microfibre towel.
4. Refine with 10P or 100P as needed, then apply suitable protection.

AP Premium Heavy Duty Cutting Compound

Use for professional heavy correction only after a test spot confirms it is needed. Follow the label for pad choice and machine settings. The listing recommends following with 10P Medium Rubbing Compound and 100P Zero Swirl Polish.

10P Medium Rubbing Compound

Use for light-to-moderate defects or to refine after heavy cutting. Follow the product instructions for pad, quantity and working method, wipe residue and inspect. Continue with 100P where further refinement is needed. The listing does not provide numeric machine settings.

100P Zero Swirl Rubbing Compound

Use after 10P or directly on lightly defected paint. Apply a small amount to a finishing pad, work small sections at the label-recommended settings and wipe with a clean microfibre towel. The listing describes low-to-medium speed without a numeric setting. Follow with 200P for further refinement if needed, or apply suitable protection.

200P Finest Zero Swirl Finishing Polish

Use as the final refinement step where required to address remaining haze and micro-marring. Follow the bottle for pad choice, application and working settings. Remove residue and prepare the paint for the chosen sealant or coating.

Wax, Sealants & Quick Protection

All In One Silicone Liquid Polish

1. Start with clean, dry paint on a cool surface in the shade.
2. Apply a small amount to a foam applicator or microfibre cloth.
3. Work in small sections using circular motions.
4. The listing specifies a 2–3 minute haze time, then buff with a clean, dry microfibre towel.

Follow the bottle if its directions differ. Do not assume this silicone-containing product is suitable immediately before a ceramic coating; follow the coating's preparation instructions.

Hard Magic Car Wax

Apply to a clean, compatible surface, allow to dry as directed and buff off with a clean cloth. The listing describes an apply–dry–buff method but gives no drying time. Check the label and test compatibility, especially on coated finishes.

Ceramic Paste Wax

Prepare clean, dry, compatible paint and follow the container instructions for application, haze time and buffing. The listing does not specify these timings or curing requirements.

Liquid Carnauba Wax Polish

Use on clean, compatible paint according to the bottle's application and buffing instructions. Check the required drying time before starting; it is not specified in the listing.

Spray Wax Sealant

Use as a quick protection step on a clean, compatible finish. Follow the label for whether to apply wet or dry, spray quantity and wiping method. These details are not specified in the listing.

Spray Ceramic

This SiO2 spray is intended for paint protection. Clean the surface and check the bottle for wet-or-dry application, spray quantity, levelling or rinsing method and curing requirements. Do not assume it uses the same method as a bottled ceramic coating.

Ceramic & Graphene Coatings

Ceramic Pre Treatment Spray

Use before coating to remove oils and wax or polish residues. Follow the bottle's application and wiping instructions, and ensure the surface meets the chosen coating's preparation requirements before proceeding.

10H Ceramic Coating

The current listing specifies professional application only.

1. Ensure the surface is clean, dry and prepared, with paint correction completed where needed.
2. Place the coating cloth over the coating sponge and apply coating liquid to the cloth.
3. Spread evenly in horizontal and vertical lines over a 1 ft × 1 ft area.
4. The listing specifies a 3–5 second flash time, followed by wiping and polishing with a microfibre towel. Follow the supplied instructions if they differ for your conditions.
5. Work in a shaded, dust-free environment. Confirm curing and water-avoidance times from the supplied instructions before starting.

9H Ceramic Coating

The kit listing includes a 50 ml coating, two applicator pads and two coating cloths. Prepare the surface according to the supplied instructions. Check the 9H-specific application, flash, levelling and curing directions before use; do not borrow the 10H timings.

Graphene Coating 50 ml

Professional application is recommended. Complete any required paint correction and surface preparation first. Follow the supplied graphene-specific instructions for application, flash time, levelling and curing. The listing does not provide these settings.

10H Ceramic Coating — Pack of 5 Bottles

Check each bottle's supplied directions and confirm it is the same formulation as the individual 10H product before following that guide. The multipack listing does not provide application or curing instructions.

9H Ceramic Coating — Pack of 5 Bottles

Follow the instructions supplied with this pack. Confirm preparation, application, flash and curing requirements before starting; the multipack listing does not specify them.

Exclusive Coating — Pack of 5 Bottles

Obtain the Exclusive Coating instruction sheet before applying. Its listing does not specify surface preparation, application method, flash time or curing time. Do not substitute instructions from the 9H, 10H or graphene products.

Graphene Coating — Pack of 5 Bottles

This listing currently has no product description or usage directions. Contact Auto Bros for the exact formulation's instructions before use. Do not assume the individual 50 ml product's method applies.

Accessories & Kits

MicroFiber Cloth

Use a clean cloth suitable for the task. Separate paint, glass, interior and wheel cloths, and change to a clean face as residue builds up. Do not wipe dirty paint with a dry cloth. Wash according to the cloth's care instructions.

Applicator Pads — Pack of 3

1. Apply a small amount of the chosen product to a clean pad.
2. Spread evenly in small sections with light circular or straight-line motions, following that product's directions.
3. Keep one pad per product type to avoid cross-contamination.
4. For products that permit it, rinse the pad thoroughly and air-dry after use. Follow special handling or disposal instructions for coating-contaminated applicators.

Car Care Kit 11Pcs

Identify the products included in your box and follow each one's guide above and its bottle instructions. A typical routine is wash, targeted cleaning, correction only if needed, then compatible protection and finishing. The current kit listing does not name all 11 items, so do not assume a particular product is included.

Car Care Kit Small

Check the contents supplied in your kit, then follow the matching individual product guides. Start with washing, continue with any necessary cleaning and finish with compatible protection. The current listing does not provide an itemised contents list.

Need Product-Specific Help?

Contact Auto Bros with the exact product name, a photo of its label and the surface you want to treat. Confirm missing dilution, contact-time or curing instructions before application, especially for concentrated cleaners and professional coatings.